A Do-It-Yourself Guide To Making A Weed Grinder

how to make a grinder for weed?Why spend your hard-earned money on an expensive grinder when you can easily make one at home? It’s actually quite simple to make a grinder for weed, and all you need is a few household supplies.
 
A grinder is a device that breaks up the cannabis flower into smaller pieces, which makes it easier to vape. There are many different types of grinders on the market, but they all serve the same purpose.

In this article, we will show you how to make a grinder for weed. This grinder is easy to make and only requires a few tools and materials. But before that, if you are outdoors or traveling, there are not so many tools to make a grinder, I will first teach you how to grind weeds without a grinder

The following is an introduction to the best way to grind weeds when there is no grinder

 grind weed with a credit card

A lot of people ask us how we get our weed so finely ground up for rolling joints. The answer is simple: a credit card! Credit cards are great for grinding up your cannabis because they’re thin and flexible, which allows them to move through your bud more easily than other tools like scissors or knives.
 
To use a credit card grinder, simply place the desired amount of cannabis on a hard surface and press down on the weed with your thumb or fingers until it is finely ground (but not so much that it turns into dust!).
 
In addition to being convenient, credit card grinders are also very portable — they can fit in your pocket or wallet — making them very easy to take with you wherever you go. If you’re going camping or traveling somewhere where smoking isn’t allowed , for example, having a good credit card grinder on hand can be really helpful!
 grind weed with a credit card

rolling paper and a coin

You can also use a rolling paper and a coin or bobby pin to break up your buds. That’s how I used to roll joints back in high school when I didn’t have any papers on me (and even then, I always had at least one).
 
If you want to go even more low-tech, try using two pieces of fabric one on top of the other (a towel will work) and rubbing them together until there are enough small bits for you to smoke.
rolling paper and a coin

with scissors

Take a pair of sharp scissors and cut the weed into small pieces. You can use any kind of scissors for this, but make sure they are sharp enough to cut through the weed easily. You may also want to wear gloves when you do this because it can get messy. The marijuana will be ground into small pieces that you can then use to roll a joint or smoke in a pipe.
 
The scissors method is not recommended because it doesn’t work as well as other methods of grinding your weed. This method does not remove all of the stem from your buds and leaves more residue on them than necessary.
with scissors

Use paper bag and hammer to grind weed

Use a hammer and a paper bag to grind weed. First, remove the stems and seeds from your bud. Then pack the weed into a paper bag. Fold down the top of the bag and use a hammer to bash it, until it’s small enough for your pipe or joint. This method may take some practice, but it’s one of the cheapest ways to go when you’re grinding up some weed on your own in just minutes!
 
But be aware that The friction from hitting the bag will heat up the marijuana and cause it to release its oils into the air. You can also use a Electric Herb Grinder or Marijuana Grinder with Handle, the above is to grind weeds without grinder The best way, of course, if you have a lot of time, or have a lot of tools at home, then you can try diy grinder for weed

Here’s how to make a weed grinder at home:

Making a grinder for weed is a simple process that anyone can do with a few basic tools. The first step is to gather the supplies you will need, which include a drill, a small saw, and some sandpaper.
 
1) Find a suitable container
 
You’re going to need some sort of container that has holes in it (ideally with multiple layers). You’ll also want it to be tough enough that it won’t break when you put pressure on it. The most common containers used include pill bottles (both plastic and glass), mason jars, wood or even soda cans!
 
Next, you will need to measure and mark the dimensions of the grinder you want to make. Once the dimensions are marked, you will need to cut out the pieces of the grinder using the saw. After the pieces are cut out, you will need to sand them down so that they are smooth. Finally, you will need to drill a hole in the center of the grinder so that the weed can be placed inside.
 
2) Drill holes into the container
 
Drill several small holes into the lid of your chosen container using a drill bit that’s slightly larger than the seeds or pollen you want to grind up. Once you’re done you can grind your marijuana

Leave a Reply

Your email address will not be published. Required fields are marked *

The maximum upload file size: 256 MB. You can upload: image, audio, video. Links to YouTube, Facebook, Twitter and other services inserted in the comment text will be automatically embedded. Drop files here

We are here for you!